High Voltage Power Supplies from Applied Kilovolts



KS series datasheet

KS5, KS10, KS20 & KS30

GENERAL PURPOSE HIGH VOLTAGE MODULES

5kV, 10kV, 20kV & 30kV
High frequency switch mode control
Internal control or externally programmable
Short circuit and flashover proof
24 hour burn in
Low radiated magnetic field

Pin Connections & Safety Instructions

**ELECTRICAL SPECIFICATION**
unit type	polarity	output	ripple at full load
KS5P	positive	50 volts to 5kV at 1mA	< 0.02% peak to peak
KS5N	negative	50 volts to 5kV at 1mA	< 0.02% peak to peak
KS10P	positive	100 volts to 10kV at 0.5mA	< 0.02% peak to peak
KS10N	negative	100 volts to 10kV at 0.5mA	< 0.02% peak to peak
KS20P	positive	250 volts to 20kV at 0.2mA	< 0.02% peak to peak
KS20N	negative	250 volts to 20kV at 0.2mA	< 0.02% peak to peak
KS30P	positive	500 volts to 30kV at 0.1mA	< 0.02% peak to peak
KS30N	negative	500 volts to 30kV at 0.1mA	< 0.02% peak to peak

INPUT VOLTAGE: - 24 volt d.c. +10% at less than 0.5A. Negative input terminal common to HV earth return.

OUTPUT VOLTAGE: - See separate table.

LINE REGULATION: - Less than 0.1% of maximum voltage for input changes of 1 volt.

LOAD REGULATION: - Less than 0.1% of maximum voltage for load changes from 10% to full load. (Measured at maximum voltage).

OVERLOAD PROTECTION: - Flashover and short circuit proof.

TEMPERATURE CO-EFFICIENT: - 300ppm/ °C or better.

CONTROL:

INTERNAL potentiometer.

EXTERNAL potentiometer or 10V analogue signal. (0 to +10V gives zero to maximum output, tolerance +2%). Input impedance > 100Kohm.

READOUT: - Voltage monitor 0 to +10V represents zero to maximum output, source resistance 10 kohm.

CURRENT MONITOR: - Optional on all units. Note- current monitor includes the internally used feedback current.

OPERATING TEMPERATURE: - 0 °C to +45 °C

STORAGE TEMPERATURE: - -35 °C to +85 °C

R.F.I.: - Steel case for low radiated magnetic field.

TAP: - +500 volt tap at 0.5mA (tracks main output, not available with current monitor option).

MECHANICAL SPECIFICATION

SIZE: All units 115 x 98 x 47mm

OUTPUT: By 0.5 meter screened cable

INPUT CONNECTOR: Molex 10 pin, mating connector supplied.

	Applied Kilovolts Ltd. http://www.appliedkilovolts.com/ 38 - 40 Eastbrook Road, Portslade, Sussex, BN41 1PB, United Kingdom Phone: +44 (0) 1273 439 440 Fax: +44 (0) 1273 439 449
Local distributor in Japan	APACE Science, Inc. http://www.apace-science.com/ Mitomo-Bldg.#2 - 6F, Ebisu-nishi 2-Chome, 2 - 8, Shibuya-Ku, Tokyo 150-0021 Phone: +81 (0)3 - 3463 - 3204 Fax: +81 (0)3 - 3463 - 3205

INPUT VOLTAGE: -	24 volt d.c. +10% at less than 0.5A. Negative input terminal common to HV earth return.

OUTPUT VOLTAGE: -	See separate table.

LINE REGULATION: -	Less than 0.1% of maximum voltage for input changes of 1 volt.

LOAD REGULATION: -	Less than 0.1% of maximum voltage for load changes from 10% to full load. (Measured at maximum voltage).

OVERLOAD PROTECTION: -	Flashover and short circuit proof.

TEMPERATURE CO-EFFICIENT: -	300ppm/ °C or better.

CONTROL:
INTERNAL potentiometer. EXTERNAL potentiometer or 10V analogue signal. (0 to +10V gives zero to maximum output, tolerance +2%). Input impedance > 100Kohm.

READOUT: -	Voltage monitor 0 to +10V represents zero to maximum output, source resistance 10 kohm.

CURRENT MONITOR: -	Optional on all units. Note- current monitor includes the internally used feedback current.

OPERATING TEMPERATURE: -	0 °C to +45 °C

STORAGE TEMPERATURE: -	-35 °C to +85 °C

R.F.I.: -	Steel case for low radiated magnetic field.

TAP: -	+500 volt tap at 0.5mA (tracks main output, not available with current monitor option).

MECHANICAL SPECIFICATION
SIZE:	All units 115 x 98 x 47mm

OUTPUT:	By 0.5 meter screened cable

INPUT CONNECTOR:	Molex 10 pin, mating connector supplied.